Download Brochures :
Heat and Mass Balance Software
Heat & Mass Balance With ease of SINGLE Page USER INterface
Simple Heat Balance is a software program which creates heat balance diagrams (HBD) for a Rankine cycle based steam power plant.
It is the best software available for creating HBDs considering that it is accurate as well as user friendly . Whereas other softwares need thousands of inputs to configure the software and may take hours or days for the same. Simple Heat Balance needs less than 100 inputs, and even a beginner can accustom himself/herself within a few hours and get results without compromising with accuracy.
One can simulate the software with different configurations of system like single LP or double LP, HP, IP or HP-IP combined, turbine, HP heaters out of service, super critical, ultra super-critical conditions, backward or forward cascading of heaters, BFP turbine/ motor or motor+turbine, and other conditions in design and off design modes. (see below)
It has been tested with different manufacturers’ systems and reflected unmatched accuracy, with less than 0.5 % deviation from the correct values.
The adaptable design helps engineers to keep their focus where it is actually required. Inside complexities have been handled by our software professionals for you. A single software has the capacity to simulate the system in design and off-design mode and also to provide cost estimates. Output of this software can be saved and printed in form of a diagram (as you always prefer to do)
Many new users have reported that they didn’t felt need of any training or reference manual while working on this. A few minutes exploring of the software is enough for generating the valuable simulation data. For veterans starting modeling is matter of few minutes.
This seemingly contradictory combination of incredible power and detail with fast, user friendly and intuitive user interface is the result of thoughtful software designs and tireless improvements that our experts have put into the product. All input variables have reasonable default values. Non-critical inputs are tucked away into side menus, readily accessible to those who want them, but virtually unnoticed while modeling the general and common plant configurations. While choosing for somewhat new configuration, you will always be amazed by the details and their depth. At GreenSync Solutions, we follow the Simple Yet Powerful (SYP) design principle which is also our cutting edge USP.
Fully Flexible Program
Simple Heat Balance allows the user to choose from the combination of LP (4) heaters and HP (3) Heaters, with choice of possible number of extraction points for heaters. Heater drips can be cascaded forward or backward. Sliding pressure mode or constant pressure mode of operation can be simulated.
The user can select the combination of drive for BFP turbine. Steam source to deaerator, BFP turbine, SH spray and Reheater spray can be selected. The user can select double LP exhaust or single LP exhaust. Condenser pressure of both the LP cylinders can be independently selected. Provision for selecting HP-IP arrangement is provided which automatically modifies the gland sealing arrangement.
The Simple Heat Balance program also offers the user to simulate off-design conditions such as target which may differ from the rated load. It also gives you an opportunity to simulate bypass heaters, effect of spray in super heater or reheater, varying the steam parameters, change of pressure etc
If you are interested in the software or want to know more, please contact us and our professionals will be responding to your queries. You can also download brochure through the links provided in right panel.
Features:
- Suitable for matching your requirements while engineering Super Critical or Ultra super critical plants
- Works in design and off design mode (NO two separate licenses are required),
- Higher accuracy as compared to existing products
- Requires minimum inputs,
- Does not require any formal training (saving in significant professional time)
- Seamless transition between design and off design mode
- Unique single page user interface (copyrighted design)
- Very little configuration time
- 1997 steam table specifications have been used
- WYSIWYG printing of the cycle
Possible Configurations:
Different Configurations of cycle are possible while simulation what if scenarios:
- Single reheat/ double reheat
- Single LP/ double LP
- HP – IP combined and separate
- Variation in cylinder extraction
- Forward / backward cascading of heaters
- Selection of units
- Turbine/ motor driven BFP and combination thereof
- This is just an introduction. (almost all practical requirements can be configured and simulated through this software)
Our Other Products
Your concern is plant efficiency and economy. We understand! That’s why we have a wide range software products for your convenience.
Psychometric Chart: stand alone software as well as libraries
Steam Table: Stand alone software as well as libraries